Modeling and simulation of plastic deformation of Aluminium ASTM A1200 during mechanical conformed process

Authors

  • Luis C Juiña Universidad Politécnica Salesiana
  • Víctor H Cabrera Universidad Politécnica Salesiana
  • Nancy V Moreno Universidad Politécnica Salesiana
  • Cristian A Anrango Universidad Politécnica Salesiana

DOI:

https://doi.org/10.29019/enfoqueute.v10n1.375

Keywords:

aluminium; conformed; strain; finite elements; simulation

Abstract

The research evaluates the behavior of a material when a plastic deformation occurs. The document describes the analytical process, finite elements and integrate process in order to develop shaped piece plan. Stress analysis and section variation were analyzed during the stuffing process. In the experimental part, the mechanical characteristics of the aluminum ASTM A1200 were determined (Yield strength was 214 MPa). The shaping process was carried out in a 5 tons press with pneumatic device. Several tests were executed with different depths in order to compare thicknesses with the physical model simulation. The maximum error was 3.67 % at 15 mm depth and the minimum of 0.24 % with the total depth. Respect to the efforts generated during the conforming, the maximum and minimum errors were 10.9 % and 2.18 % respectively.

Downloads

Download data is not yet available.

References

ANSYS. (2013). ANSYS Mechanical APDL Basic Analysis Guide. Pensilvania: SAS IP.
Bernal Aguilar, Y. (2013). Planeación de procesos de embutido de chapa mediante herramientas numéricas. Revista Centro Azúcar, 29-38.
Bravo Vargas, S., y Reta, C. (2016). Desarrollo de un modelo virtual para conformado de aceros inoxidables. 8va. Congreso internacional de Ingeniería Electromecánica y de Sistemas, 1-6.
Campos Vasquéz, A., Escamilla Navarro, A., y González López, A. (2013). Análisis experimental-numérico de la plantilla para el conformado plástico mediante embutido de una abrazadera metálica. Científica, 67-76.
Escribano, A. I., y Herranz, R. A. (2014). DEDUCETU. Retrieved from DEDUCETU: http://de-duce-tu.blogspot.com/p/embuticion-2.html
Fuentes Quisaguano, M. X., y Mullapa Rumipamba, M. (2008, Enero). Matriz de embutición y corte para la implementación del laboratorio de matricería. Quito. Retrieved from Repositorio Digital EPN: http://bibdigital.epn.edu.ec/bitstream/15000/2005/1/CD-1202.pdf
Groover, M. P. (2007). Fundamentos de Manufactura Moderna (3ª. ed.). CDMX, México: The McGraw-Hill.
Kalpakjian, S. (2008). Manufactura, ingeniería y tecnología (5ª. ed.). CDMX, México: Pearson Educación.
Kurt, M., y Juvinall, C. R. (2013). Diseño de elementos de maquinas. madrid: Limusa.
López Navarro , T. (1976). Troquelado y Estampación (5ª. ed.). Barcelona, España: Gustavo Gili.
Oehler, G., y Kaiser. (1977). Herramientas de troquelar, estampar y embutir (6ª. ed.). Barcelona, España: Gustavo Gili.
Osrodala. (junio 9 de 2012). Wikemedia Commons. Retrieved from Wikemedia Commons: https://commons.wikimedia.org/wiki/File:EMBUTIDO_general.jpg
Rodríguez, M., y González, A. (2012). Elasticidad y resistencia de materiales I. Madrid, España: Universidad Nacional de Educación a Distancia.
Rossi, M. (1979). Estampado en frío de la chapa (9ª. ed.). Madrid, España: DOSSAT, S.A.
Villamar Palacios, V. H. (2008). Diseño de una prensa hidraulica para elaborar pocetas de acero inoxidable. Guayaquil: s. e.
Vinueza Lozada, A. F., y Gutierrez Suquillo, N. R. (2018). Análisis por el método de elementos finitos del comportamiento de las pastillas de freno ABS con base de acero y zinc al discretizar el elemento contínuo al utilizar software CAE. Enfoque UTE, 188-203.
Zienkiewicz, O. C. (2007). El método de los elementos finitos. Barcelona, España: Reverté.

Downloads

Published

2019-03-29

How to Cite

Juiña, L. C., Cabrera, V. H., Moreno, N. V., & Anrango, C. A. (2019). Modeling and simulation of plastic deformation of Aluminium ASTM A1200 during mechanical conformed process. Enfoque UTE, 10(1), pp. 128 – 140. https://doi.org/10.29019/enfoqueute.v10n1.375

Issue

Vol. 10 No. 1 (2019)

Section

Automation and Control, Mechatronics, Electromechanics, Automotive

License

The articles and research published by the UTE University are carried out under the Open Access regime in electronic format.  This means that all content is freely available without charge to the user or his/her institution. Users are allowed to read, download, copy, distribute, print, search, or link to the full texts of the articles, or use them for any other lawful purpose, without asking prior permission from the publisher or the author. This is in accordance with the BOAI definition of open access. By submitting an article to any of the scientific journals of the UTE University, the author or authors accept these conditions.

The UTE applies the Creative Commons Attribution (CC-BY) license to articles in its scientific journals. Under this open access license, as an author you agree that anyone may reuse your article in whole or in part for any purpose, free of charge, including commercial purposes. Anyone can copy, distribute or reuse the content as long as the author and original source are correctly cited. This facilitates freedom of reuse and also ensures that content can be extracted without barriers for research needs.

 

This work is licensed under a Creative Commons Attribution 3.0 International (CC BY 3.0).

 

The Enfoque UTE journal guarantees and declares that authors always retain all copyrights and full publishing rights without restrictions [© The Author(s)]. Acknowledgment (BY): Any exploitation of the work is allowed, including a commercial purpose, as well as the creation of derivative works, the distribution of which is also allowed without any restriction.