Sliding modes control for a heat Exchange system: experimental validation

Authors

  • Maribel Cecilia Pérez Pirela Universidad de Guadalajara
  • Juan Paulo García Sandoval Universidad de Guadalajara

DOI:

https://doi.org/10.29019/enfoqueute.v9n4.404

Keywords:

cable direct driven robot; sliding mode control; Fuzzy controller; PI controller; kinematic

Abstract

Sliding modes control (SMC) is a nonlinear control method with a systematic design procedure that allows to obtain a explicit solution for the control input. This method has some advantages, such as robustness against external disturbances and unpredictable parametric variations. On this work, two conventional SMC techniques, one using the error and other using the error integral, are designed and validated in a heat exchange system composed of a single pass circulation electric heater, whose control objective is to regulate the output temperature of the fluid, under the influence of external disturbances, such as variations in the flow and inflow temperature, manipulating the electric current passing through the heater resistance. The two SMC algorithms are analyzed using numerical simulations and their performance is compared through the integral absolute error and the integral absolute control input, selecting the best one to be tested experimentally. The experimental results indicate that the SMC is capable of fulfilling the control objective with satisfactory performance. 

Keywords: Conventional sliding modes control; heat exchange system; nonlinear control.

Downloads

Download data is not yet available.

Author Biography

Juan Paulo García Sandoval, Universidad de Guadalajara

El Doctor Juan Paulo García Sandoval es Profesor Investigador de tiempo completo Titular “C” adscrito al Departamento de Ingeniería Química de la Universidad de Guadalajara. Cursó estudios de Licenciatura en Ingeniería Química y de Maestría en Ciencias de la Ingeniería Química en la Universidad de Guadalajara. Realizó estudios de Doctorado en Ciencias en la Especialidad de Ingeniería Eléctrica en el Cinvestav-IPN.

References

Ataei, M., & Shafiei, S. E. (2008). Sliding mode PID-controller design for robot manipulators by using fuzzy tuning approach. En Proceedings of the 27th Chinese control conference (pp. 16–18). Citeseer.
Babaghasabha, R., Khosravi, M. A., & Taghirad, H. D. (2014). Adaptive Control of KNTU Planar Cable-Driven Parallel Robot with Uncertainties in Dynamic and Kinematic Parameters. Recuperado 26 de octubre de 2018, de /paper/Adaptive-Control-of-KNTU-Planar-Cable-Driven-Robot-Babaghasabha-Khosravi/3cf12282c9a37211f8f7adbc5e667a1436317626
Camacho, O., & Smith, C. A. (2000). Sliding mode control: an approach to regulate nonlinear chemical processes. ISA Transactions, 39(2), 205-218. https://doi.org/10.1016/S0019-0578(99)00043-9
Gallina, P., Rossi, A., & Williams II, R. L. (2001). Planar cable-direct-driven robots, part ii: Dynamics and control. En ASME. DECT2001 ASME Design Engineering Technical Conference. Pittsburgh: ASME Publisher (Vol. 2, pp. 1241–1247).
Ghosh, A., Sen, S., & Dey, C. (2015). Design and real-time implementation of a fuzzy PI controller on a servo speed control application. En Signal Processing and Integrated Networks (SPIN), 2015 2nd International Conference on (pp. 384–387). IEEE.
Herrera. (2017). A Blended Sliding Mode Control with Linear Quadratic Integral Control based on Reduced Order Model for a VTOL System. Recuperado de http://repositorio.educacionsuperior.gob.ec/handle/28000/4641
Jin, X., Jun, D. I., Pott, A., Park, S., Park, J.-O., & Ko, S. Y. (2013). Four-cable-driven parallel robot. 제어로봇시스템학회 국제학술대회 논문집, 879–883.
Khosravi, M. A., & Taghirad, H. D. (2014). Robust PID control of fully-constrained cable driven parallel robots. Mechatronics, 24(2), 87–97.
Nabi, A. (2013). Design of fuzzy logic PD controller for a position control system. International Journal of Engineering and Management Research, 3(2).
Oh, S.-R., & Agrawal, S. K. (2003). Cable-suspended planar parallel robots with redundant cables: Controllers with positive cable tensions. En IEEE International Conference on Robotics and Automation (Vol. 3, pp. 3023–3028). IEEE; 1999.
Palm, R. (1992). Sliding mode fuzzy control. En Fuzzy Systems, 1992., IEEE International Conference on (pp. 519–526). IEEE.
Villacres, J., Herrera, M., Sotomayor, N., & Camacho, O. (2017). A fuzzy sliding mode controller from a reduced order model: A mobile robot experimental application. En Control, Decision and Information Technologies (CoDIT), 2017 4th International Conference on (pp. 0674–0678). IEEE.
Williams Ii, R. L., & Gallina, P. (2003). Translational planar cable-direct-driven robots. Journal of Intelligent and Robotic systems, 37(1), 69–96.
Williams, R. L., Gallina, P., & Rossi, A. (2001). Planar cable-direct-driven robots, part i: Kinematics and statics. En Proceedings of the 2001 ASME Design Technical Conference, 27th Design Automation Conference (pp. 178–186).
Zanotto, D. (2011). Analysis and development of cable-driven robotic devices.

Downloads

Published

2018-12-21

How to Cite

Pérez Pirela, M. C., & García Sandoval, J. P. (2018). Sliding modes control for a heat Exchange system: experimental validation. Enfoque UTE, 9(4), pp. 110 – 119. https://doi.org/10.29019/enfoqueute.v9n4.404

Issue

Vol. 9 No. 4 (2018)

Section

Automation and Control, Mechatronics, Electromechanics, Automotive

License

The articles and research published by the UTE University are carried out under the Open Access regime in electronic format.  This means that all content is freely available without charge to the user or his/her institution. Users are allowed to read, download, copy, distribute, print, search, or link to the full texts of the articles, or use them for any other lawful purpose, without asking prior permission from the publisher or the author. This is in accordance with the BOAI definition of open access. By submitting an article to any of the scientific journals of the UTE University, the author or authors accept these conditions.

The UTE applies the Creative Commons Attribution (CC-BY) license to articles in its scientific journals. Under this open access license, as an author you agree that anyone may reuse your article in whole or in part for any purpose, free of charge, including commercial purposes. Anyone can copy, distribute or reuse the content as long as the author and original source are correctly cited. This facilitates freedom of reuse and also ensures that content can be extracted without barriers for research needs.

 

This work is licensed under a Creative Commons Attribution 3.0 International (CC BY 3.0).

 

The Enfoque UTE journal guarantees and declares that authors always retain all copyrights and full publishing rights without restrictions [© The Author(s)]. Acknowledgment (BY): Any exploitation of the work is allowed, including a commercial purpose, as well as the creation of derivative works, the distribution of which is also allowed without any restriction.